Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Just about everyone maintains their personal rationale in relation to Installing A Bathtub.
Mounting a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is conveniently obtainable, the task can move immediately; if you have to open a wall to eliminate the old tub and position the new bathtub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and also set in the new one. Ensure you have actually certified on your own for the work and also fit attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This article will certainly help you install a new tub in your bathroom if you have actually already acquired a brand-new tub as well as do not need to alter the arrangement of your previous supply of water pipes.
Your devices as well as material list need to make up the following:
Planning for the Installation
First of all, the supporting frame provided with the bath needs to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to avoid strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing faucets can be quite problematic due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bath tub in the needed placement. The wood boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water and also check all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as likewise check the overflow outlet as well as the normal outlet for leaks.
Ultimately, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bathtub should wait till the tub has been made use of a minimum of once as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers are in place in between the faucet and also the sink. Protect the tap in position with the producer offered backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous kind must be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to crack an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes and cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealant can split relatively very early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Installing A Bathtub. Many thanks for taking time to browse our posting. In case you enjoyed reading our blog entry plz do not forget to share it. Thanks for your time spent reading it.
For best results, ring! Report this page